UPCOMING EVENT: PHOENIX BASS FISHING LEAGUE - 2020 - Lake Mitchell

How to Make a Swimbait a Line-Thru

How to Make a Swimbait a Line-Thru

Jake Lawrence thinks the line-thru swimbait is more versatile than many tournament anglers realize. The Kentucky Lake and Pickwick guide and 2018 Costa FLW Series Lake Barkley champion frequently chucks one any time bass are shallow to not only put big fish in the boat, but to catch five good ones in a day.

To Lawrence, however, a line-thru isn’t just a type of swimbait to go out and buy. Thanks to the Fattube Line Thru Swimbait Tube and a lot of experimental rigging on his part, he’s able to convert his favorite “standard” swimbaits into line-thrus. It’s become an entire swimbait system that he’s refined for use throughout most of the tournament season.

 

The very basics

If you’ve never thrown a line-thru before, here are the basics:

  • Most have solid soft-plastic bodies, where the line passes through the nose of the bait and out the belly.
  • A treble hook is tied on and pricked into the underside of the swimbait.
  • Most prerigged line-thrus come with internal weights that are carefully placed to keep the bait running upright, straight and true.
  • Weight usually must be added to convert a standard swimbait to a linethru. The Fattube – a brass tube with a rim on one end – adds the weight and provides the tube through which the line is passed.

 

Where and when

While there are a few line-thru models weighted for fishing deep water, Lawrence says he usually reserves this swimbait style for when bass are in about 8 feet of water or less, and often fishes it close enough to the surface to see fish roll on it when they bite.

That doesn’t mean he’s strictly bank fishing.

“I’m fishing it offshore and on the bank, as long as it’s in 8 feet of water or less,” he says. “I just can’t keep that bait deep enough for anything deeper. About 6 or 7 feet is about as deep as I’ll keep it.”

The other factor is the exposed hook. A line-thru is a very “hangy bait,” says Lawrence.

“You cannot throw it around cover very well at all. If the fish are very loose around the cover and not tucked up against a log or inside a stake bed, like on a cloudy day or low-pressure day, and they’re aggressive and will come and get it, then I’ll throw it around cover. But generally this is an open-water type of technique. I’ve not found a weedless version of this system that will give you the same action in the swimbait.”

In Lawrence’s home region of the Tennessee Valley and west Tennessee, common target areas are channel-swing banks, lead-in banks in the mouths of spawning pockets, shallow flats, and shallow main-lake river bars or ledges. On highland lakes, it’s great around rock transitions and points. Lawrence will occasionally throw it around grass as long as it’s “really clean” grass that he can snap free of without gunking up the hook.

“During the shad spawn it’s a great way to catch them around boat docks, riprap and that sort of stuff,” he adds. “Essentially, any time they are feeding primarily on shad and there’s not a whole lot of cover around, I’ll experiment with it from the beginning of March or even February, through about the middle of May.”

After that, in Lawrence’s region, postspawn bass tend to push out to deeper offshore areas. They don’t start moving back shallow until about the middle of July. So from mid-summer through fall, he’ll break out the line-thrus again.

“Then these fish [on the Tennessee River] will leave the main river and go to shallow bars or get in the back of the bays. And I’ll pick it right back up.”

The late-summer and fall shallow-bar pattern is a frequent big-money winner in T-H Marine FLW Bass Fishing League events along the Tennessee River system of reservoirs, particularly on Kentucky Lake. With a big walking bait and one of these line-thrus, it’s possible to put some real giant gizzard shad eaters in the boat.

 

The action of the system

Line-thrus are often praised for the “free-sliding” hook setup, but that’s not specifically why Lawrence uses them.

“That line-thru gives the swimbait a totally different action,” he says. “There are a million swimbaits out there, and a lot of them are good. Take a Jenko 4-inch Booty Shaker; that is a great swimbait to fish on a jighead. It has a lot of great action. It catches them on a jighead. But you rig that on a line-thru, and it gives it a totally different action and look.

“What’s really cool about that line-thru, and I learn new things about it all the time, is each swimbait kind of has its own action when you rig it that way,” Lawrence adds. “A Keitech gets a lot of head wobble. That’s really what I’m getting when I change from a jighead over to this line-thru. You don’t have this huge weight over the head that basically guides that swimbait where it’s going. When you put the Fattube in it [to make it a line-thru], you’re giving freedom to that bait. It has secondary action. Not only does it have the paddle-tail action, but now it’s also got that head wobble that’s unique, and something you don’t get with a jighead.”

In Lawrence’s opinion, the difference can be substantial in clear water (he says his home lakes are continuously clearing up, making the line-thru a bigger factor) and around pressured fish that have been bombarded with every swimbait on the market.

“I’ve got enough confidence in this bait that once I get a bite or two on it, I’ll pretty much lock it in my hand,” Lawrence says. “I feel like if I can get this around fish they’ll bite it.”

 

Favorite swimbaits

Pre-rigged line-thrus such as the Scottsboro Tackle Co. Line Through and Optimum Boom Boom Line Thru are great options if you don’t want to bother tinkering with terminal tackle. You can buy them off the shelf and go catch fish. Lawrence prefers the versatility of carrying a few standard swimbaits that he can rig several ways based on the situation.

The swimbaits he most commonly rigs himself are the solid-bodied Jenko Booty Shaker, Scottsboro Tackle Co. Swimbait (technically a hollow swimbait) and Keitech Swing Impact FAT, though he’s experimented with several others, including some older Ignite baits (shown top in this photo). Hollow paddle tails like the Zoom Swimmer and Basstrix are difficult to rig consistently with the Fattube, so Lawrence reserves those for other scenarios.

 

Experimentation

Lawrence’s best advice for figuring out all the subtleties of the line-thru rigging style is to avoid trying to rig every swimbait in every size. Just pick three swimbait variations you’re confident in, and tweak the terminal tackle until it’s just right.

The construction of the swimbait, its size, the weight of the Fattube used and other factors all dictate the action and running depth. Lawrence has spent hours tinkering, experimenting with new terminal tackle and trying to get more performance from his baits. In fact, in the course of working on this article, he changed his split ring preference (now opting more often to not use one to connect the hook) and discovered a new treble hook (more on it later) that helps reduce snags.

Generally, the first step is to figure out what size Fattube is needed to balance out each size of your chosen swimbaits to get it to run right.

“The lighter the weight, the more of that head-wobble action you’re going to get,” Lawrence says. “But the fatter or bulkier that swimbait is, the more you’ll have to adjust because if it has a really fat head, that causes the bait to rise. A Jenko 4.0 Booty Shaker has a really big, bulky head on it. To make that run in the 1- to 3-foot range, I’ve got to use a 1/4-ounce Fattube on it. If I use a 4.8 Keitech, I use a 1/8-ounce Fattube.

“Where I primarily throw that Jenko Booty Shaker is when I want to fish really shallow. A lot of times, later in the fall, when they have seen a million Evergreen SB 125s and a million Sexy Dawgs, you can go right behind somebody that’s throwing topwater ultra-shallow on bars that are 1 foot or less and throw the Booty Shaker and catch them.”

The Scottsboro and Keitech, which have narrower heads and mouths, like to run a little deeper. Also, the Keitech has a more subtle action (but still with head wobble) than the wide-wobbling Booty Shaker, so Lawrence reserves the Keitech for situations when he needs a little more finesse.

If you’re trying to incorporate smaller swimbaits, you might also have to consider the length of the Fattube. If it runs too far back into a swimbait, the tube can limit the action. There’s a weightless plastic version that can work, or you can use a pop rivet in its place. In that case it’s probably necessary to add small nail weights into the belly of the swimbait to help keep it stable during the retrieve. Again, experimentation is the only way to figure it out.

 

Rigging the Fattube

To rig the Fattube, the No. 1 tip is to keep the bait perfectly straight. The steps depends on the specifics of the swimbait.

Here’s Lawrence’s method for rigging a 4.0 Booty Shaker:

 

1. Rest the swimbait on its side, and align the Fattube on the outside. The large end should be under the belly. Lawrence likes the small end to stay inside the plastic and remain about 1/16 to 1/8 inch shy of protruding out the nose. Use your thumb or some other means to mark where it needs to be inserted into the belly to wind up in the right place. This is pretty easy on the Booty Shaker because of its open underside, which is flanked by two “belly flaps” that hang down. The Fattube should rest under the belly inside those flaps. On other swimbaits, nailing the entry point is critical.

 

2. Run a toothpick through the swimbait from the point you marked on the belly out the center of the bait’s nose. You could also use a stiff metal wire. The key is to work very slowly to make sure the toothpick travels in a perfectly straight line through the bait’s body. If you bend the bait, it will stay kinked, and the rigged swimbait could swim off line or roll. If you get off line with the toothpick, back out and redirect so everything stays straight. Lawrence goes a little at a time and eyeballs the bait to make sure he gets it just right.

 

3. Leave the toothpick in place, and line up the Fattube on the rear point.

 

4. Push the Fattube through the plastic, following the toothpick. You can then remove the toothpick. With some swimbaits, the only remaining steps would be to run the line through the tube and tie on a hook, but Lawrence does a couple extra steps with the Booty Shaker because of its open underside.

 

5. Squeeze the side flaps toward the center. They don’t need to touch, but should close up slightly to hold the Fattube in place. Run a toothpick through the side flaps so it skims across the Fattube. Depending on the size Fattube and swimbait you’re using, you might be able to get away with just one toothpick. Others might require two. If you can get the toothpick to pass right in front of the Fattube’s rim, even better. The toothpick keeps everything together in place.

 

6. Cut off the excess toothpick material, leaving just a hair extending out the sides, and put a drop of glue on each end of the toothpick.

 

7. Feeding the line through the nose can be a frustrating part. It might help to widen the hole in the nose plastic just a hair by “drilling” a little with a toothpick. Then slip the line into the nose, through the Fattube and out the belly.

 

8. Tie on the appropriate treble hook and you’re done.

 

A few rigging notes:

 

1. Watch your back angle – On some swimbaits, such as the Keitech, the “rim” of the Fattube will press against the belly and impart an arch in the bait’s back (see No. 2 for more on this). It’s better to start in “neutral” with a straight back. To get there, press the Fattube rim up into the plastic (it’ll cut in just a tad) to relieve the tension and straighten the bait.

 

2. Use split rings or don’t – Lawrence used to use a split ring to attach the hook all the time. Now, he typically goes without it. It really depends on how the hook he’s using rests against the bait. When using a split ring to connect the hook, only the split ring or the hook eye can rest flat against the bait’s underside – not both. If the hook eye isn’t flat, the barbs might not line up properly. That’s why Lawrence goes with whichever connection method results in the most streamlined rigging for the bait and hook he’s using.

 

3. Position the hook correctly – The best way to extend the life of the swimbait is to position the hook so the knot is inside the Fattube and the hook eye (or split ring, if using one) is against the Fattube. This way, all the pulling pressure of the cast and retrieve is directed into the back of the tube.

“If you leave any gap between the split ring or hook and Fattube, when you cast, you’re putting all of that oomph of your cast into that hook bend,” Lawrence says. “You’ll tear the plastic, and the hook will move.”

However, Lawrence says you can actually tweak the running depth of the bait based on where you stick the hook. Going farther back by 1/8 inch or so will create a very slight back arch that helps the swimbait dig a little deeper. You can reverse the bend to fish shallower by adjusting where you insert the hook.

Lawrence advises to skin-hook the treble with the smallest amount of the hook as possible. He typically inserts it up to the point where the bend begins.

 

4. Choose the right hook – The right hook size depends on the size of the bait and the model you’re using. Lawrence typically uses 2X Gamakatsu treble hooks, but he recently discovered the Owner Stinger Treble Short Shank STY-35MF. On this hook, the points don’t radiate out at equal angles. The bottom two points stick out closer to 90 degrees from the top barb, so when rigged in the Booty Shaker’s belly the bottom points “hide” behind the side flaps, which helps to reduce snags. Lawrence used a No. 4 to rig the 4.0 Booty Shaker shown in this article.

5. Don’t be afraid to destroy some baits – According to Lawrence, you’ll probably booger up a bait or two as you’re dialing in the process. That’s OK. It’s just part of the process of dialing in the peculiarities of each swimbait. Also, always test a rigged bait in the water to make sure it’s tracking straight and not rolling to one side.

 

Tactics and presentations

In addition to limitations on depth, Lawrence also restricts himself to more or less only one presentation when using a line-thru.

“The one thing you do lose with the line-thru version is the ability to make the swimbait do anything different or really deviate very far from a standard slow wind,” he explains. “Why that is I can’t exactly explain. The standard, and almost always the only way I can get them to bite it, is just a slow, steady wind.”

The only variation he adds is to help trick followers into biting.

“About every 10 cranks or so I will make one very fast half-turn of the reel,” Lawrence says. “In this clear water, they will chase this bait, track it, and get right in behind and not bite it. If you make that swimbait do something just a little different, it can make them eat it. But as far as making any twitch of the rod tip or anything like that, it seems like they won’t bite it.”

 

Rods, reels and line

Lawrence throws most line-thrus on a medium-heavy, moderate-fast Jenko DCVR Gambler Series rod with a Daiwa Tatula 150 reel (6.3:1) and fluorocarbon line. Rod length can vary from 7-6 to 7-1. He says it’s not necessary to have a big swimbait “whuppin’ stick.” Like with any treble hook bait, the line-thru swimbait needs to be fished on a rod with enough tip action and forgiveness to not rip out the hooks. A hard hookset generally is unnecessary. For most situations, 15-pound-test line is fine, but Lawrence upgrades to 20- or 25-pound test in the fall to help keep the bait up in the water column on very shallow ledges.

 

Give it a shot

One of the great parts about Lawrence’s system is that you don’t have to stock a bunch of extra swimbaits to add line-thrus to your arsenal. You should already be carrying spare treble hooks and split rings. Just stock some Fattubes and toothpicks, learn to rig your favorite swimbaits you’re already carrying and you’ve just added another valuable tool to your arsenal.

Tags: swimbait  -line-thru  -tennessee-river  -shad  -fall  -spring  curtis-niedermier  tips-and-techniques 

Review: Yakima TopWater

Review: Yakima TopWater

The TopWater retails for $549 and has more bells and whistles than most of the other rooftop rod storage options out there. For some anglers, those extras would be much appreciated and worth the money, but for others they might be overkill. READ MORE »

Nixon Eyeing Early June Return

Nixon Eyeing Early June Return

You couldn’t choose just one word to describe Larry Nixon’s professional fishing career. But right now, if you had to try, the most applicable word might be “resiliency.” READ MORE »

10 Pro Circuit Highlights So Far

10 Pro Circuit Highlights So Far

We’re almost halfway through the 2020 Tackle Warehouse Pro Circuit schedule, which means we’re far enough along now for a little retrospective on what’s happened thus far. READ MORE »

Sight-Fishing with Swimbaits

Sight-Fishing with Swimbaits

Ron Nelson, the Pro Circuit Angler of the Year leader and a renowned sight-fisherman, used a Keitech Swing Impact FAT for blind-fishing and sight-fishing at Martin and earned a runner-up finish. California’s Kevin Hugo took seventh at Lake Havasu and caught some of his biggest bass sight-fishing with a Little Creeper All American Trash Fish or Sunfish. Though the reasons why they settled on swimbaits varied, both pros can offer valuable lessons for any angler tackling a spawning scenario. READ MORE »

Top 10 Baits and Patterns from Havasu

Top 10 Baits and Patterns from Havasu

Results from the Toyota Series Western Division event at Lake Havasu probably didn’t surprise any Western anglers who are familiar with the fishery. For folks in other parts of the country that might only have followed FLW’s early February events on the Colorado River reservoir, the tournament results might have opened some eyes to just how good the fishing can be on Havasu. Particularly on day one, the lake delivered, kicking out 12 limits of more than 20 pounds, including Tai Au’s limit of 26 pounds, 1 ounce. The success on day one resulted from a perfect storm of conditions for catching spawning bass on beds.  READ MORE »

Co-angler Farage Gets Win No. 5

Co-angler Farage Gets Win No. 5

If you weren’t already aware, you need to be paying attention to the name Jack Farage. This week, the Discovery Bay, Calif., co-angler won his fifth Toyota Series Western Division tournament since 2013 by catching 43 pounds, 3 ounces at Lake Havasu. For his latest win, Farage earned a Phoenix 518 Pro with a 115-hp Suzuki outboard. READ MORE »

Au Finishes Strong at Lake Havasu

Au Finishes Strong at Lake Havasu

Tai Au of Glendale, Ariz., weighed in a five-bass limit worth 16 pounds, 15 ounces today to finish off a wire-to-wire win at the Toyota Series Western Division season opener on Lake Havasu. Au’s three-day total was 61-3.  READ MORE »

Lake Havasu Midday Update – Day 3

Lake Havasu Midday Update – Day 3

It was another slow morning on Lake Havasu at the Toyota Series Western Division opener. Though, that was to be expected. Most of the top 10 pros have had their best luck in the middle of the day and early afternoon. Mornings have been tough. READ MORE »

Au Stays Ahead on Tougher Day Two

Au Stays Ahead on Tougher Day Two

Tournament leader Tai Au managed to stay in first place by recognizing key environmental factors and knowing when to change up his baits. Yesterday, four of the five bass that Au weighed in were bass he caught sight-fishing. Today, he didn’t look at any of the bass he brought to the scale. Au still managed to weigh in 18 pounds, 3 ounces, taking his two-day total to 44-4. He’s searching for his first FLW victory this week.  READ MORE »

Lake Havasu Midday Update – Day 2

Lake Havasu Midday Update – Day 2

After an afternoon and evening of intense rainfall yesterday, the Lake Havasu City area finally got a break from the precipitation today. But instead of rain, the anglers fishing the Toyota Series Western Division opener on Lake Havasu have had to deal with a stiff southerly wind that’s made it tough to sight-fish, some dirtier water in areas (particularly in the upper end) and a drop in water temperature of a couple of degrees. Not surprisingly of a post-frontal day, the fishing has been much more difficult so far on Friday.  READ MORE »

Au Clobbers 26-1 for Havasu Lead

Au Clobbers 26-1 for Havasu Lead

Tai Au of Glendale, Ariz., took the lead on day one of the Toyota Series Western Division event at Lake Havasu with a five-bass limit that weighed 26 pounds, 1 ounce. Au heads up a roster of Western hammers that managed to tally 12 limits of more than 20 pounds today.  READ MORE »

Lake Havasu Midday Update – Day 1

Lake Havasu Midday Update – Day 1

The fishing is hot at Lake Havasu. By 9:30, many of the anglers we’d seen on the water for day one of the Toyota Series Western Division season opener already had limits or had kicker largemouths in the box. Most of those fish were caught off beds, with the majority being caught sight-fishing and the rest coming just by fishing through likely spawning areas. Others were caught out in front of spawning areas and around marinas. The fishing should only get better, too. Currently, there are scattered rain showers, but the sun is shining across many parts of the reservoir, making it a little easier to spot fish on beds.  READ MORE »

Two Species Spawning at Havasu 

Two Species Spawning at Havasu 

The weatherman did it again. About two weeks prior to today’s kickoff for the Toyota Series Western Division season at Lake Havasu, the forecast called for highs in the mid-80s and sunshine for three straight days during the tournament. Instead, practice was rainy, and the current forecast calls for precipitation for at least the first two days and highs that likely won’t top 70 degrees.  READ MORE »

Wheeler Should Produce Mega Mixed Bags in March

Wheeler Should Produce Mega Mixed Bags in March

If you love mixed bags of big largemouth and smallmouth bass (and who doesn’t?), you’re going to want to pay close attention to the Toyota Series Southeastern Division opener on Wheeler Lake March 26-28. Local pro Sam George, who fishes the Tackle Warehouse Pro Circuit, expects to see mid-20-pound limits cross the weigh-in stage, and predicts the winner will almost certainly weigh both green and brown fish. READ MORE »

College Open Prize Pool Bigger than Ever

College Open Prize Pool Bigger than Ever

The annual Abu Garcia College Fishing presented by YETI Open returns to Kentucky Lake and Lake Barkley in mid-March for the sixth consecutive season. This time around, however, the stakes are even higher, as teams compete for a brand-new Phoenix 518 Pro bass boat, 20 spots in the 2021 National Championship and 20 spots in the all-new Major League Fishing College Faceoff presented by Wiley X in Raleigh, N.C., later this spring. READ MORE »

Red-Hot Spawn Bite Expected at Havasu

Red-Hot Spawn Bite Expected at Havasu

Spawning bass and spring break will be the story lines at the Toyota Series Western Division opener at Lake Havasu in mid-March. Well, OK … the spawning bass will certainly be the main focus of the anglers. But dealing with traffic from pleasure boaters will definitely contribute to the pros’ decision-making, particularly on the weekend.  READ MORE »

Prespawn Showdown Coming to Ross Barnett

Prespawn Showdown Coming to Ross Barnett

The Phoenix Bass Fishing League presented by T-H Marine kicks off its 2020 Mississippi Division schedule at Ross Barnett Reservoir on March 7. Ross Barnett is an annual early season stop for FLW and the first crack at gaining essential points in the race to qualify for this fall’s Regional. This time around, anglers might have to navigate tricky conditions due to a wet and rainy winter. READ MORE »

Perfect Practice Conditions at Harris

Perfect Practice Conditions at Harris

Ask Matt Becker how his practice is going for this week’s Tackle Warehouse Pro Circuit event presented by Bad Boy Mowers on the Harris Chain, and the Pennsylvania pro has nothing to complain about. For starters, he’s in the Sunshine State, and it’s about 80 degrees. The 50-degree swing compared to what folks back home in Finleyville, Pa., are experiencing is certainly pleasant. The fishing has also been pretty good through a day and a half of practice. READ MORE »

Timing Right for Giant Weights at Chickamauga

Timing Right for Giant Weights at Chickamauga

If it’s big bass you want, late winter and early spring are ideal times to catch them at Lake Chickamauga, which is why the 2020 Toyota Series Central Division opener is perfectly timed to be a big-bass slugfest. The tournament, which runs Feb. 27-29, could produce some of the biggest five-bass limits FLW will see all year. Just how good the fishing will be depends on the weather, and whether the region ever sees an end to the rain that’s been falling recently.  READ MORE »

Big Bags Expected at Bama Division Kickoff on Lake Martin

Big Bags Expected at Bama Division Kickoff on Lake Martin

Big largemouths and lots of spots are the main attractions at Alabama’s Lake Martin, where the Phoenix Bass Fishing League presented by T-H Marine Bama Division kicks off its 2020 season Feb. 8. Local hammer David Gaston, who’s won the last two Bama events at Martin, expects a typical wintertime tournament this season with solid weights across the board. READ MORE »